LASAT COMMUNICATIONS A/S CREDIT 288 Card Type Modem (asynchronous) Chipset Unidentified Maximum Data Rate 28.8Kbps Maximum Fax Rate 14.4Kbps Data Modulation Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC Fax Modulation Unidentified Error Correction/Compression MNP5, MNP10, V.42, V.42bis Fax Class Class I & II Data Bus PCMCIA Type II 53856 SUPPORTED STANDARD COMMANDS Basic AT Commands +++, ‘comma’, A/ A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z &C, &D, &F, &G, &K, &P, &R, &S, &T, &V, &W, &Y, &Z Extended AT Commands \A, \B, \G, \J, \K, \L, \N %C, %E, %L, %Q Special AT Commands :E, *H, -K, )M, @M, +MS, -Q S-Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S16, S18, S24, S25, S26, S29, S30, S31 S32, S33, S36, S38, S39, S46, S48, S82, S86, S91, S92, S95, S201 Note: See MHI help file for complete information. UNIDENTIFIED COMMANDS Command Default S14 Unidentified S21 Unidentified S22 Unidentified S23 Unidentified S27 Unidentified S28 Unidentified S37 Unidentified S40 Unidentified S41 Unidentified Proprietary AT Command Set AUTOSYNC OPTIONS Type: Register Format AT [cmds] S19=n [cmds] Default: 26 Range: 0 - 30 Description: Controls autosync protocol, HDLC address detection, bit coding, and HDLC idle. Bit Value Function 0 0 Not used 1 0 Binary synchronous protocol used. 1 HDLC protocol used. 2 0 HDLC address detect disabled. 1 HDLC address detect enabled. 3 0 NRZI bit coding used. 1 NRZ bit coding used. 4 0 HDLC idle sends MARK. 1 HDLC idle sends FLAG or SYNC. AUTOSYNC HDLC ADDRESS Type: Register Format: AT [cmds] S20=n [cmds] Default: 0 Range: 0-255 Unit: Unidentified Description: Sets the HDLC address and binary synchronous character. COUNTRY CODE Type: Configuration Format: AT [cmds] *NCn [cmds] Description: Sets the factory defaults according to the country specified. The next power-up or ATZ command will reset the modem to the appropriate defaults. DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials the telephone number indicated according to any modifiers included in the string. Command Function DJ MNP10 link will be negotiated at 1200bps for this call. DK MNP10 power level adjustment enabled for this call. DL Re-dial last number. DP Pulse dialing enabled. DS=n Dial stored telephone number n. DT Tone dialing enabled. DW Dialing resumed following dial tone detection. D, Dialing paused for amount of time specified in S8 register. D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D^ Calling tone disabled for this call. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. DISPLAY BLACKLIST NUMBERS Type: Immediate Format: AT [cmds] *B [cmds] Description: Displays the list of all the numbers on the blacklist and their statuses. DISPLAY DELAYED NUMBERS Type: Immediate Format: AT [cmds] *D [cmds] Description: Displays the list of all delayed numbers and their statuses. DISPLAY INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested about the modem. Command Function I0 Displays product identification code. I1 Displays ROM checksum. I2 Tests and reports ROM checksum. I3 Displays firmware revision. I5 Displays country code. DISPLAY STORED NUMBERS Type: Immediate Format: AT [cmds] \F [cmds] Description: Displays all stored telephone numbers. PULSE DIALING MODE Type: Configuration Format: AT [cmds] *Zn [cmds] Description: Selects the type of pulse dialing the modem will use. Command Function *Z0 Modem will use pulse dialing type 0. *Z1 Modem will use pulse dialing type 1.